The ICP-M4SA is an Australian-made 4 head servo automatic filling machine, designed by ICP Packaging Machines Australia for small and medium businesses and contract packers. It brings servo control, saved product setups and fast changeovers to businesses that could never justify a custom-built line.
ICP-M4SA at a glance
- 4 servo-driven piston heads with bottom-up fill (BUF).
- Omron servo drives, PLC and touchscreen HMI.
- Fill and BUF speed adjustable through every fill.
- Saves product setups for fast changeovers.
- Very low compressed-air use: about 20 L/min.
- Australian made, 12-month warranty, available to hire or buy.
Why We Built It
Traditional pneumatic multi-head fillers are tough and reliable, but every product change means adjusting and test-filling until the volume is right, and getting the best from them takes an experienced operator. For a contract packer running several products a day, that adds up to a lot of lost time.
The ICP-M4SA was designed to remove that. Settings are saved and recalled on the touchscreen, so changeovers take minutes, and staff with minimal training can run it with confidence.
Control Over Every Fill
Because each piston is driven by a servo motor, you control the speed through the whole fill, not just the start and finish. Start slowly so the product doesn’t splash, ramp up through the middle of the fill, then slow down again as the product reaches the neck of the container. The bottom-up fill speed can be set the same way, keeping foamy products under control.
You can also fine-tune fills live while the machine is running, instead of stopping for repeated test fills.
Built to Last
Quality controls
Omron servo drives, PLC and HMI: proven industrial components built for years of use.
Low air use
The servo drive means the machine uses about 20 L/min of compressed air, so you don’t need a large compressor or big power bills.
Sensors built in
Container sensors are built into the machine, and container gates are standard, so no separate sensor box is needed.
Industrial build
Built like every ICP machine: for our own hire fleet, with food-contact parts designed to be easily cleaned and sanitised.
Specifications
| Feature | ICP-M4SA |
|---|---|
| Filling heads | 4 servo-driven pistons |
| Piston sizes | 140 ml, 320 ml, 500 ml and 1.3 L |
| Minimum fill | 14 ml |
| Fill method | Bottom-up fill (BUF), speed adjustable through the fill |
| Controls | Omron servo drives, PLC and touchscreen HMI |
| Compressed air | About 20 L/min |
| Container detection | Sensors built in, container gates standard |
| Warranty | 12 months (T&Cs apply) |
| Made in | Australia, Australian Made logo |
Who It Suits
The ICP-M4SA suits growing producers who have outgrown single-head filling, and contract packers who change products often. If you only run one or two products, a pneumatic twin head such as the ICP-M2RV may be all you need. Our guide to manual, semi-automatic and automatic fillers helps you compare.
The best way to know is to try it. The ICP-M4SA is available to hire, so you can run your own products before you buy.
Frequently Asked Questions
Common questions about the ICP-M4SA 4 head servo filler.
What is the ICP-M4SA?
The ICP-M4SA is an Australian-made 4 head servo automatic liquid filling machine with Omron servo drives, PLC and HMI, designed for small and medium businesses and contract packers.
What fill volumes can the ICP-M4SA handle?
It takes 140 ml, 320 ml, 500 ml and 1.3 L pistons, with a minimum fill of 14 ml.
Do I need a large compressor for the ICP-M4SA?
No. Because the pistons are servo driven, the machine uses about 20 L/min of compressed air.
Can I hire the ICP-M4SA?
Yes. The ICP-M4SA is available to hire or buy from Rentafill, so you can trial it on your own products first.
What warranty does the ICP-M4SA have?
A new ICP-M4SA carries a 12-month warranty (T&Cs apply), plus free phone and video support for the original purchaser.
See the ICP-M4SA in Action
Hire it and run your own products, or talk to us about buying one.


